Bitushape-p

Thương hiệu: (Đang cập nhật ...) Loại: chống thấm

Liên hệ

Màng chống thấm BITUSHAPE là màng chống thấm dẻo, được sản xuất từ hỗn hợp giầu bitum và hợp chất polymers APP được chọn lọc , có khả năng chịu nhiệt, chống tia tử ngoại UV và khả năng chống thấm cao

chinh-sach
Giao hàng toàn quốc
chinh-sach
Giao hàng ngay sau khi đặt hàng
chinh-sach
Tư vấn 24/7

BITUSHAPE - P
APP MODIFIED BITUMEN PLASTOMERIC WATERPROOFING MEMBRANE
REINFORCED WITH SPUNBOND NON WOVEN POLYESTER
What is BITUSHAPE - P?
Produced by the Modern Waterproofing Company, BITUSHAPE-P is a line of polymer-modified bitumen waterproofing membrane of the highest quality.
BITUSHAPE-P is modified by APP and APAO, thus guaranteeing superior performance under various conditions.
BITUSHAPE - P is reinforced with Spun bond Non-woven Polyester (P) which provides high mechanical properties.
Uses
BITUSHAPE - P is a general purpose membrane, can be applied virtually anywhere where torch applied modified bitumen membranes subject to light to moderate mechanical stresses are specified, and normal low temperature performance is required.
BITUSHAPE - P can be applied in:
 Single layer roofing system for normal use
 Double layer roofing system combined with BITUSHAPE –G fiberglass reinforced
 Waterproofing of toilets & wet area inside buildings
 Slab on grade
BITUSHAPE - P with Mineral Slated Finish is recommended for exposed roofing system (Unprotected) for Non-accessible roofs or roofs subject to low traffic conditions
Advantages
BITUSHAPE - P has been designed with special regard to providing clients with an excellent and versatile product.
Advantages of BITUSHAPE – P include:
 Easy to apply (by torch)
 High mechanical properties
 Absolute impermeability to water pressure
 Excellent high temperature performance
 Excellent adhesion on any surface
 High dimensional stability
 Environmentally friendly
Quality Control
The Modern Waterproofing Company is ISO 9001 certified. It applies a stringent quality control system utilizing its in-house laboratory. Occasional samples are analyzed by independent laboratories to ensure continued adherence to the highest standards (ASTM, EN, etc.).
Each roll of BITUSHAPE is individually coded with a label containing all necessary information about the roll. This is intended to ensure tractability in accordance with ISO control standards.
Product Range
Standard thickness available includes 3mm and 4mm. Some types could be available by weight 3kg/m2 and 4kg/m2.
Bottom surface finish is normally Polyethylene Film (PE).
Upper surface finish choices include:
 Polyethylene Film (PE)
 Fine Sand (S)
 Mineral Slated Grey (GY)
 Mineral Slated Green (GRN)
 Mineral slated White (WT)
 Mineral slated Red (RD)
Slated rolls are available in 4kg, 4.5kg and 5kg per square meter.
The nominal length of each roll is 10 meters and the nominal width is one meter.
Special specification can be designed based on client’s needs.
BITUSHAPE - P
APP MODIFIED BITUMEN PLASTOMERIC WATERPROOFING MEMBRANE
REINFORCED WITH SPUNBOND NON WOVEN POLYESTER
NOTES:
 Above results are based on 4mm membrane
 Tolerance within 20% of the above results for mechanical characteristics complies with the tolerance specification of (ASTM, EN)
 Due to constant product improvements, MODERN company reserves the right to change above values without advance notice
STORAGE:
 BITUSHAPE membranes should be stored vertically in well covered and ventilated place not subject to direct sunlight
APPLICATION INSTRUCTIONS:
 BITUSHAPE membranes are installed by propane torch welding method, loose laid or fully bonded to the substrate depending on system requirements
 While unloading from truck the rolls shall by no means allowed to fall or be thrown down from the truck
 To avoid applying the membrane to corners with 90 °C angle, sand cement cant strip 5x5 cm should be executed at horizontal - vertical intersections
 Surface to be waterproofed should be clean, dry, free from dust and smooth, in case of irregular surface a sand cement screed is recommended
 Before laying BITUSHAPE membranes, surface should be primed with cold applied bituminous primer (NIROL – S) or (NIROL – W
 Membrane is unrolled and placed in aligned position
 Each roll should overlap the next by 10cm side laps and 15cm staggered end laps
 Then, membrane should be re-rolled about half of its length without changing its orientation
 Using a propane gas torch the membrane is un-rolled again slowly while applying the flame to the entire exposed lower face (For fully bonded system) - until the plastic cover film burns off and the bituminous mass starts melting, thus creating a heat weld between the membrane and the substrate
 Then, torching of the seams takes place by heating the contact line at side and end laps by torch from above, pressing the upper membrane on to the lower one using a trowel, the torch has to be carefully used avoiding to keep the flame on the same point for too long
 For sloping roofs start laying the membrane from the lower edge with longitudinal direction of rolls perpendicular to slope direction, side lap of next roll to be placed above the first one, etc…
For detailed application procedures please refer to BITUMODE MAUAL GUIDE, where you can find construction detail drawings
Modern Waterproofing Company
2, El Sobki St., Dahabi Sq., Heliopolis, Cairo, Egypt
Tel.: (+20 2) 4141003 (8 Lines)
Fax: (+20 2) 2912315
www.bitumode.com E-mail: info@modernwaterproofing.com TECHNICAL DATA TEST METHOD UNIT RESULT الخواص الفنية
Roll Length EN 1848-1 EN 1848-1 EN 1849-1 EN 1849-1 m 10 الطول
Roll Width m 1 العرض
Thickness for PE finish mm 2, 3 , 4 , 5 السمك لتشطيب السطح بولى ايثلين
Weight for slated surface finish kg 4, 4.5 , 5 الوزن لتشطيب السطح الحصوة
Softening Point (Ring & Ball)
ASTM D-36
oc
≥ 150
درجة الليونة )اختبار الحلقة و الكرة(
Penetration at 25 oc ASTM D-5 dmm 15 to 25 عند 25 مئوية º
درجة الاختراق
60 oc dmm 60 to 80 عند 60 مئوية º
Cold Flexibility
EN 1109
oc
0
المرونة عند درجات الحرارة المنخفضة
Heat Resistance
EN 1110
ºc
120
الثبات عند درجات الحرارة العالية
Reinforcement
gm/m2
Non-woven Polyester
التسليح
Tensile strength Long EN 12311-1 N/5cm 750 طولي ا
مقاومة الشد القصوى
Wide N/5cm 600 عرضي ا
Elongation at break
Long
EN 12311-1
%
≥ 40
طولي ا
الاستطالة القصوى
Wide
%
≥ 42
عرضي ا
Tear Resistance (Nail – Shank) Long EN 12310-1 N 150 طولي ا مقاومة التمزق
طبقا للمواصفات الاوربية Wide N 200 عرضي ا
Tensile-tear Resistance
Long
ASTM D-5147
N
550
طولي ا
مقاومة التمزق
طبقا للمواصفات الامريكية
Wide
N
450
عرضي ا
Joint tensile strength Long ASTM D-5147 N 650 طولي ا مقاومة الشد عند اماكن
الركوب Wide N 500 عرضي ا
Dimensional stability
Long
EN 1107-1
%
± 0.2
طولي ا
ثبات الأبعاد
Wide
%
± 0.1
عرضي ا
Water absorption ASTM D-5147 % 0.15 max. درجة امتصاص الماء
Static puncture resistance
EN 12730:2000
L4
مقاومة الاختراق الاستاتيكى
Dynamic puncture resistance EN 12691 - I4 مقاومة الاختراق الديناميكى
Water impermeability at 100 K pa
EN 1928:2000
-
Absolutely impermeable
مقاومة نفاذية الماء عند 100 كيلو بسكال
Impermeability to water vapor
EN 1931
μ
80,000
نفاذية بخار الماء
Ageing due to U.V. radiation
EN 1296
-
Pass
مقاومة التقادم للاشعة فوق البنفسجية
Resistance to thermal ageing EN 1296 - No signs of deterioration after the test مقاومة التقادم الحرارى
Adhesion to concrete
EN 13596
N/cm
40
الالتصاق بالاسطح الخرسانية
Thermal conductivity ASTM C-177 Kcal/mh oc 0.12 الموصلية الحرارية
Dielectric constant ( k )
ASTM D-150
-
2.5
قيمة الثابت الكهربائى
Dielectric rigidity - Kv/mm 14 صلابة العزل الكهربائى
Average Granule loss for Mineral Slated Finish ASTM D-4977 gm/m2 Less than 200 متوسط قيمة الفقد للحبيبات فى حالة الشرائح
ذات تشطيب السطح العلوى بالحصوة الأردواز

popup

Số lượng:

Tổng tiền: